8.5-11.0 ghz gaas power amplifier flange, 10 pin page 1 of 6 p1006-fa august 2006 - rev 16-aug-06 mimix broadband, inc., 10795 rockley rd., houston, texas 77099 tel: 281.988.4600 fax: 281.988.4615 mimixbroadband.com characteristic data and specifications are subject to change without notice. ? 2006 mimix broadband, inc. export of this item may require appropriate export licensing from the u.s. government. in purchasing these parts, u.s. domestic customers accept their obligation to be compliant with u.s. export laws. mimix broadband ? s three stage 8.5-11.0 ghz gaas packaged power amplifier has a large signal gain of 21.5 db with a +40.5 dbm saturated output power. this device uses mimix broadband ? s 0.5 m gaas phemt device model technology, and is based upon optical gate lithography to ensure high repeatability and uniformity. the device comes in a 10 pin, high frequency, lcc flange package. the package has a copper composite base material and a laminated ceramic substrate. this device is well suited for radar applications. x-band 10w power amplifier flange package 21.5 db large signal gain +40.5 dbm saturated output power 37% power added efficiency 100% on-wafer rf, dc and output power testing features general description electrical characteristics (pulsed mode f=10khz, duty cycle=5%, t a =25oc) parameter frequency range (f ) input return loss (s11) 1 output return loss (s22) 1 large signal gain (s21) gain flatness ( s21) reverse isolation (s12) 1 saturated output power (p sat ) power added efficiency (pae) drain bias voltage (vd1,2,3) gate bias voltage (vg) supply current (id) (vd=8.0v, vg=-0.6v typical) units ghz db db db db db dbm % vdc vdc a min. 8.5 - - - - - - - - - - typ. - 15.0 12.0 21.5 +/-0.5 60.0 +40.5 37 +8.0 -0.6 4.0 max. 11.0 - - - - - - - +9.0 - 4.5 absolute maximum ratings supply voltage (vd) supply current (id) gate bias voltage (vg) input power (pin) storage temperature (tstg) operating temperature (ta) channel temperature (tch) +9.0 vdc 4.5 a +0.0 vdc tbd -65 to +165 o c -55 to mttf table mttf table 1 (1) channel temperature affects a device's mttf. it is recommended to keep channel temperature as low as possible for maximum life. (1) measured on-wafer pre-packaging. 1
august 2006 - rev 16-aug-06 page 2 of 6 power amplifier measurements (pulsed mode f=10khz, duty cycle=5%, t a =25oc) mimix broadband, inc., 10795 rockley rd., houston, texas 77099 tel: 281.988.4600 fax: 281.988.4615 mimixbroadband.com characteristic data and specifications are subject to change without notice. ? 2006 mimix broadband, inc. export of this item may require appropriate export licensing from the u.s. government. in purchasing these parts, u.s. domestic customers accept their obligation to be compliant with u.s. export laws. 8.5-11.0 ghz gaas power amplifier flange, 10 pin p1006-fa psat (dbm), pin = 19 dbm (25 devices) 0 5 10 15 20 25 30 35 40 45 7.5 8.0 8.5 9.0 9.5 10.0 10.5 11.0 11.5 freq (ghz) psat (dbm) psat (dbm), pin = 19 dbm (25 devices) 34 35 36 37 38 39 40 41 42 43 44 7.5 8.0 8.5 9.0 9.5 10.0 10.5 11.0 11.5 freq (ghz) psat (dbm) large signal gain (db), pin = 19 dbm (25 devices) 0 5 10 15 20 25 7.5 8.0 8.5 9.0 9.5 10.0 10.5 11.0 11.5 freq (ghz) gain (db) large signal gain (db), pin = 19 dbm (25 devices) 15 16 17 18 19 20 21 22 23 7.5 8.0 8.5 9.0 9.5 10.0 10.5 11.0 11.5 freq (ghz) gain (db) pae (%), pin = 19 dbm (25 devices) 0% 5% 10% 15% 20% 25% 30% 35% 40% 45% 50% 7.5 8.0 8.5 9.0 9.5 10.0 10.5 11.0 11.5 freq (ghz) pae (%) drain currents (a), 5 us pulse, pin = 19 dbm (25 devices) 0.0 0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 4.5 7.5 8.0 8.5 9.0 9.5 10.0 10.5 11.0 11.5 freq (ghz) id (a)
august 2006 - rev 16-aug-06 page 3 of 6 power amplifier measurements (pulsed mode f=10khz, duty cycle=5%, t a =25oc) mimix broadband, inc., 10795 rockley rd., houston, texas 77099 tel: 281.988.4600 fax: 281.988.4615 mimixbroadband.com characteristic data and specifications are subject to change without notice. ? 2006 mimix broadband, inc. export of this item may require appropriate export licensing from the u.s. government. in purchasing these parts, u.s. domestic customers accept their obligation to be compliant with u.s. export laws. 8.5-11.0 ghz gaas power amplifier flange, 10 pin p1006-fa gate bias (v), (25 devices) -0.7 -0.6 -0.5 -0.4 -0.3 -0.2 -0.1 0.0 7.5 8.0 8.5 9.0 9.5 10.0 10.5 11.0 11.5 freq (ghz) vg (v) following test conditions apply for all measured data unless otherwise stated: vd = 8.0v, 4.0a. pin = +20dbm, temp = +25c, pulsed duty cycle = 5% xp1006-fa, pout vs temp. 30.0 32.0 34.0 36.0 38.0 40.0 42.0 44.0 8 8.5 9 9.5 10 10.5 11 11.5 12 rf (ghz) pout (dbm) +25 c -40 c +85 c xp1006-fa, pout vs applied dc voltage 30.0 32.0 34.0 36.0 38.0 40.0 42.0 44.0 8 8.5 9 9.5 10 10.5 11 11.5 12 rf (ghz) pout (dbm) 8v, 4a 6v, 4a 7v, 4a xp1006-fa, pout vs dc current 30.0 32.0 34.0 36.0 38.0 40.0 42.0 44.0 8 8.5 9 9.5 10 10.5 11 11.5 12 rf (ghz) pout (dbm) 8v, 3a 8v, 4a 8v, 5a xp1006-fa, pout vs pulse duty cycle 30.0 32.0 34.0 36.0 38.0 40.0 42.0 44.0 8 8.5 9 9.5 10 10.5 11 11.5 12 rf (ghz) pout (dbm) 5% 10% 25%
august 2006 - rev 16-aug-06 page 4 of 6 physical dimensions functional schematic pin designations (note: engineering designator is i0004966) mimix broadband, inc., 10795 rockley rd., houston, texas 77099 tel: 281.988.4600 fax: 281.988.4615 mimixbroadband.com characteristic data and specifications are subject to change without notice. ? 2006 mimix broadband, inc. export of this item may require appropriate export licensing from the u.s. government. in purchasing these parts, u.s. domestic customers accept their obligation to be compliant with u.s. export laws. 8.5-11.0 ghz gaas power amplifier flange, 10 pin p1006-fa g d d 1 2 3 4 6 5 7 8 9 10 pin description typ. values 0 (flange) gnd 1vg-0.6 v 2nc 3 rf in +19.0 dbm 4nc 5nc 6 vd(3) 8.0 v 7nc 8 rf out +40.0 dbm 9nc 10 vd(1,2,3) 8.0 v
august 2006 - rev 16-aug-06 page 5 of 6 mttf mimix broadband, inc., 10795 rockley rd., houston, texas 77099 tel: 281.988.4600 fax: 281.988.4615 mimixbroadband.com characteristic data and specifications are subject to change without notice. ? 2006 mimix broadband, inc. export of this item may require appropriate export licensing from the u.s. government. in purchasing these parts, u.s. domestic customers accept their obligation to be compliant with u.s. export laws. 8.5-11.0 ghz gaas power amplifier flange, 10 pin p1006-fa xp1006-fa, mttf with rf power applied 1.0e-01 1.0e+00 1.0e+01 1.0e+02 1.0e+03 1.0e+04 1.0e+05 1.0e+06 20 30 40 50 60 70 80 90 100 110 120 backplate temperature (c) mttf (millions of hours) 100% dc duty cycle 50% dc duty cycle 30% dc duty cycle 10% dc duty cycle xp1006-fa, mttf without rf power 1.0e-02 1.0e-01 1.0e+00 1.0e+01 1.0e+02 1.0e+03 1.0e+04 1.0e+05 20 30 40 50 60 70 80 90 100 110 120 backplate temperature (c) mttf (millions of hours) 100% dc duty cycle 50% dc duty cycle 30% dc duty cycle 10% dc duty cycle mttf is calculated from accelerated life-time data of single devices and assumes an isothermal back-plate. app note [1] biasing - this device is biased with vd(1,2,3) = 8.0v and 4.0 a (pin 6,10). the drain current is controlled by the gate bias with a typical value of vg = -0.6v (pin 1). it is recommended to use active biasing to keep the currents constant as the rf pow er and temperature vary; this gives the most reproducible results. the recommended power-up sequence is described below: 1. apply -2.0 v to vg 2. apply +8.0 v to vd(1,2,3) 3. adjust vg to achieve nominal drain current 4. apply rf power 5. re-adjust vg to maintain nominal drain current. depending on the supply voltage available and the power dissipation constraints, the bias circuit may be a single transistor or a low power operational amplifier, with a low value resistor in series with the drain supply used to sense the current. the gate of t he phemt is controlled to maintain correct drain current and thus drain voltage.
august 2006 - rev 16-aug-06 page 6 of 6 handling and assembly information ordering information caution! - mimix broadband mmic products contain gallium arsenide (gaas) which can be hazardous to the human body and the environment. for safety, observe the following procedures: ? do not ingest. ? do not alter the form of this product into a gas, po wder, or liquid through burning, crushing, or chemical processing as thes e by-products are dangerous to the human body if inhaled, ingested, or swallowed. ? observe government laws and company regulations when discarding this product. this product must be discarded in accordance wi th methods specified by applicable hazardous waste procedures. life support policy - mimix broadband's products are not authorized for use as critical components in life support devices or systems without the express written approval of the president and general counsel of mimix broadband. as used herein: (1) life support devices or systems are devices or systems which, (a) are intended for sur gical implant into the body, or (b) support or sustain life, and whose failure to perform when properly used in accordance with instructions for use provided in the labeling, can be reasonably expected to resu lt in a significant injury to the user. (2) a critical component is any component of a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system, or to affect its safety or effectiveness. mounting onto circuit boards - special design considerations allow the ?fa packages to operate at high frequencies. one element required for operation at high frequency is the use of fine geometry leads. fine geometry leads are not as robust, and it is possible t o exceed the yield or tensile strength even with small hand tools. even though firmly attached, extra care in handling is essential. precautions: ? check all fixtures used for assembly, lead forming, and testing, to be sure that parts are not subjected to unnecessary physi cal stress. ? check that test sockets are easy to load, and not likely to torque or twist the leads. ? be sure that the package is attached to a flat surface. ? do not over-torque mounting screws. ? do not use conductive gaskets or shims under the package. ? do not use test fixtures or sockets that may produce a sharp lifting force on the leads. ? if packages must be removed after solder attach, do not pry the leads up so that the force lifting the lead from the board is also lifting the lead from the package. use a probe to press down on the lead-to-package joint, and lift the lead when the solder is fluid. mounting screws - 1. mounting surface should be tapped for close tolerance fit of inner to external thread 2. mounting surface must be flat 3. excessive bending or deformation of the package during mounting is likely to damage the ceramic. to avoid this: ? insert all mounting screws for a given package and tighten all finger tight. ? begin tightening screws on opposite corners of the package to 1/3 torque ? tighten following same screw position pattern to 2/3 torque ? tighten following same screw position pattern to full torque 4. the use of ground or thermal pads under the package is not recommended. part number for ordering description xp1006-fa-0n00 nickel/gold plated rohs compliant 10l flange package in bulk quantity XP1006-FA-EV1 xp1006-fa evaluation module mimix broadband, inc., 10795 rockley rd., houston, texas 77099 tel: 281.988.4600 fax: 281.988.4615 mimixbroadband.com characteristic data and specifications are subject to change without notice. ? 2006 mimix broadband, inc. export of this item may require appropriate export licensing from the u.s. government. in purchasing these parts, u.s. domestic customers accept their obligation to be compliant with u.s. export laws. 8.5-11.0 ghz gaas power amplifier flange, 10 pin p1006-fa product name length, min diameter thread pitch material torque, in-oz socket head cap screw, english 1/8" 0 80 type 316 stainless steel 1.0 socket head cap screw, english 1/8" 2 56 type 316 stainless steel 2.0 socket head cap screw, metric 6 mm m1.6 0.35mm type 316 stainless steel 1.0 socket head cap screw, metric 6 mm m2.5 0.45mm type 316 stainless steel 2.0
|
